- Patented proven push pin design
- Super easy to attach and detach from the magazine
- No specialty tools or devices required to disassemble
- One piece design, no extra parts to possibly lose during disassembly
- Designed specifically for the M&P
- CNC machined from billet aluminum
- Includes the required extra length magazine spring
- Hard Anodized
- Made in the USA
Premium-Quality Parts To Produce A Long-Wearing, Match Quality Trigger Pull
Skeletonized for low mass and faster lock time without sacrificing long wearability and strength. 2 lb. trigger pulls can be achieved without shortening the hooks below .018". All engagement surfaces are highly polished and ready for installation. Ultra Lite components are CNC machined from aerospace-quality, maraging alloy tool steel that's age- hardened to prevent stress, warpage and tolerance loss. All profiles are mechanically correct, through-holes are properly aligned so they function the first time without time consuming fitting. Exposed hammer edges are chamfered to minimize slide drag and clothing wear. Set contains the Ultra Lite Hammer plus matching Sear and Disconnector.
1911, Issue:11, Page:017
Big Book Catalog, Issue:71, Page:111
Sinclair, Issue:1A, Page:017
We combined our Premium Punch line and added a handy bench block to come up with the perfect punch set for the busy shop or department Armorer. Easily start, remove, and install spring pins and roll pins in firearms without damage to the pin or firearm.
Starter punches are used to start the removal of roll or spring pins without causing damage to the pins or the punch. Short shaft gives more control by putting your hand closer to the pin and prevents bending the longer, standard roll pin punches. Standard punches are used to finish drive the roll pin or spring pin after it’s started. Starter and standard roll pin punches feature a special tip that centers inside the hollow pin to help prevent slippage. Complete set includes bench block, also available separately.
Cleaning with UltraSonics requires the correct solution for the correct cleaning application. Lyman has partnered with a renowned chemical research team to develop the right solutions for use with today’s UltraSonic Cleaners. Lymans Turbo Sonic case cleaning solution was formulated to deliver premium results in cleaning cases inside and out. Lymans gun parts solution is the perfect choice for steel and stainless steel parts such as barrels, cylinders or other parts. Available in several sizes to suit your needs.
Specifically formulated for ultrasonic use right out of the bottle, Turbo Sonic Gun Lube displaces moisture and penetrates all the hard to reach areas of any part making it ideal for use after ultrasonic cleaning. Formulated for superior firearms lubrication and protection, the lube leaves a dry protective, lubricating film and can be reused repeatedly.
- Handy 5 Gallon Container for volume users - ideal for Power Pro users!
- Pouring spout extends for easy pouring with no mess.
1911, Issue:11, Page:069
Big Book Catalog, Issue:71, Page:327
Sinclair, Issue:5B, Page:075
Sinclair, Issue:5B, Page:077
The Kinect™ by KDG for MLOK™ is a revolutionary QD mounting system that will change the way we attach accessories to our modular weapons platforms. Much like the Sidelok™ for Picatinny attachment, Kinect™ insures proper and easy installation, eliminating common variables that would cause issues.(ie: over tightening) Although revolutionary, Kinect™ is quite simple in its operation. There are two spring-loaded wedges in the base of the Kinect™ mounting point. When you press the accessory or rail section down in the MLOK™ slot, two tiny deployment triggers get pressed against the rail firing the wedges into place. There is nothing more frustrating that fiddling with an allen wrench (if you can find it) to get your accessories on an off your weapon with traditional modular rail sections. This changes the whole dynamic of the MLOK™ system and really makes every accessory truly removable with the ability to mount it in a second when needed.
SPECS: Length: 1.68″ (42.8mm) Use with one MLOK section, Width: .82″ (20.9mm), Height (Over MLOK): .41″ (10.5mm), Finish: Black Anodized, Compatibility: Compatible with any MLOK rail system, Weight: 0.8oz.