Nordic Components MXT magazine extension tube.
- MXT extension tube for changing magazine extension length and capacity
- Available in variety of lengths between +2 and +9 (shell capacity measured with 2 3/4″ shells and may vary with shells of differing length)
- Features relief groove to eliminate barrel clamp travel and ensure repeatable placement after disassembly
- Relief groove is not centered and can be relocated by reversing the tube (thread pitch the same on both ends)
- Includes ONLY MXT tube
- May require purchase of new magazine spring if you are changing the capacity of your existing extension
Click this link to find the attachment nut for your firearm: Extension Tube Nut
Big Book Catalog, Issue:71, Page:205
SPECS: +1, +2, +3, +3B (for flush fit on 18.5″ barreled Benelli M1, M2), +4, +5, +5B (for flush fit on 21″ barreled Benelli M1, M2), +6, +7, +7B (for flush fit on 26″ barreled Benelli M1, M2), +8, +8B (for flush fit on 28″ barreled Benelli M1, M2), +9.
TSR SL (Super-Low) Series Rings. Providing an extremely low mounting solution for those special applications Precisely machined with tolerances held to .0002", give maximum scope/ring contact. Holds scope securely against recoil. Four-screw cap lets you align the reticle, tighten the left side of the cap, then the right side without the scope rotating. Radiused edges and corners help prevent snagging while providing attractive appearance. Large, clamp-nut lets you torque rings to Mil-STD 1913 (Picatinny) bases.
Height measured from top of base to center of ring.
SPECS: 5/8" (15.8mm) wide. Height measured from top of base to center of ring.
Safe, Non-Gun, For Law Enforcement & Military Training
A realistic, safe alternative to using real firearms for law enforcement training exercises and weapons retention drills. Molded from actual weapons for true-to-life detail. Strong, polyurethane plastic has steel reinforcement to prevent bending and flexing; handles and balances like an actual firearm. Safety blue color signifies this is a non-firing training aid.
“GLOCK” is a federally registered trademark of Glock, Inc. and is one of many trademarks owned by Glock, Inc. or Glock Ges.m.b.H. Brownells is an independent dealer of parts and accessories for Glock® pistols, and is not affiliated with or endorsed by Glock, Inc. or Glock Ges.m.b.H. The use of Glock on this page is merely to advertise the sale of Glock parts or components. As indicated in the product descriptions, not all parts and accessories on this site are official Glock products.
1911, Issue:11, Page:052
Big Book Catalog, Issue:71, Page:143
SPECS: Polyurethane. Safety blue color. Handgun simulators weigh approximately 9-13 oz. (255-369g) depending on model.
Barrel Nut Torq Wrench for DPMS & KAC Rifles. This wrench allows the shooter to put the exact amount of pressure needed on the barrel nut while attaching the barrel to the receiver. Constructed of 3/8 high steel with 4 lugs on each side to accommodate the DPMS and KAC Barrel Nuts. Works with any 3/8 or ½ drive torque wrench. This wrench is for 24-tooth free float barrel nuts.
AR-15, Issue:11, Page:084
Big Book Catalog, Issue:71, Page:087
SPECS: Weight - .525 lbs. Fits DPMS, R-25, Knights barrel nut patterns in .308.
Mainstay Of Any Polishing Room For Most Polishing Jobs
Spiral Stitched - used primarily for first cleaning operation on the gun with No. 140 Polish-O-Ray™ to knock off old blue, dirt and rust and bring the metal to a bright finish. Also used by some operators instead of Soft Felt wheels - being of a more flexible nature, great care must be exercised to not round edges, or funnel and elongate screw and pin holes.
Loose Muslin - used following each change of grit to smooth out grit marks and prepare the surface for the next finer grit. Also used to finish off the gun just prior to bluing.
Note: - Use enough sections to make each wheel as wide as your polishing motor will handle - a minimum of three sections to each wheel. Never try to use the same wheel for different grit numbers. After a wheel is broken-in and in use, mark it with the grit number to be used on it and direction of rotation to be turned. Will increase wheel life, give better finishes and save hours of work.
Big Book Catalog, Issue:71, Page:387
Accepts AR-15/M16 Accessories For Optimal Tactical Configurations
CNC machined aluminum chassis takes full advantage of proven technology and accepts off-the-shelf AR-15/M16 free float tubes, hand grips, receiver extensions, and buttstocks. Heavy duty upper and lower wraps-around around the original receiver to create a one-piece unit and provide the starting point for an outstanding tactical platform. Upper attaches firmly to the top of receiver for a rock-solid mount and improved accuracy. Includes a built-in Weaver-style base 6½" long that allows a variety of options for mounting optics. Radiused edges give a streamlined appearance, reduce weight, and prevent snagging. Fits factory 10/22® barreled action and trigger group, including heavy barrels up to .990" in diameter. T6 aluminum hardcoat anodized for durability.
Big Book Catalog, Issue:71, Page:186
SPECS: T6 aluminum, hardcoat anodized, matte black. 9½” (24cm) long, 1½” (3.8cm) wide, 3-5⁄16" (8.4cm) high. 23 oz. (652g) weight.