A Perfect Pairing for Your Vudu or Similar Riflescope
Rugged and lightweight, EOTech’s PRS 34mm Ring Mounts provide plenty of contact between the scope and rings to prevent slippage from recoil or bumps in the field. Four Allen head screws keep the ring caps securely in place, while the robust crossbolt clamps tightly to either any standard Picatinny flattop rail or scope base.
- Ring caps secured by 4 ultra-secure hex head cap screws
- Machined aluminum construction, tough hardcoat anodized finish
- Sold in pairs
Give your Vudu precision riflescope - and any tactical scope with a 34mm tube - the support it deserves with the EOtech’s PRS 34mm Ring Mounts.
For Offset, Scope-Ring Mounting Of Auxiliary Sights, Lights & Other Accessories
Lightweight, low-profile, railed cap replaces the existing top half of a Badger Ordnance scope ring to add an offset, three-slot Picatinny rail. Provide easy, off-axis mounting of a red dot sight, laser, light, or other tactical accessory. Allows instant transition from primary optic to a non-magnified CQB sight without breaking cheekweld. Machined from 6061 T6 aluminum billet for strength with minimal weight and hardcoat anodized for added strength. Models available to fit 30mm and 34mm Badger scope rings with 4- or 6-screw caps.
Big Book Catalog, Issue:64, Page:247
SPECS: 6061 T6 aluminum, hardcoat anodized, matte black. Rail - 1½" (3.8cm) long.
Matched Steel Rings for Stable Mounting of Tactical Scopes
Badger Ordnance USMC M40A3 34mm Scope Rings are the same rings issued by the Marines for the M40A3 Scout Sniper Rifle. To eliminate the damaging effects caused by mismatched rings, each Badger Ordnance USMC M40A3 34mm Scope Ring is precision-machined from barstock steel and serialized to ensure the pair of rings you purchase is as close to identical as possible.
- Sold in matched pairs
- Robust hex-head clamping nuts
- Torx-head ring cap screws
- Durable black oxide finish
- NSN #5365-09-511-9954
Badger Ordnance USMC M40A3 34mm Scope Rings fit MIL-STD 1913 Picatinny receiver rails and are compatible with any rifle that has such a receiver rail.
By utilizing Pos-Align Offset Inserts in Signature Rings, you can virtually sight-in your gun without moving the scope adjustments. By keeping the internal optics centered, you'll see through the scope all of the clarity, sharpness, and brightness that the optics designers intended for you to see. The offset inserts also correct for any misalignment caused by receiver holes drilled off center, or the bases or rings being slightly off perfect center. And for you 1000-yard shooters, the need for expensive tapered bases or shimming becomes a hassle and expense of the past. Gunsmith Kit includes 10 sets of each .005", .010", .020" inserts (60 total pieces).
Big Book Catalog, Issue:71, Page:262
SPECS: Synthetic, black. For 1" rings only.Gunsmith kit includes: 10 each .005", .010", .020" inserts (60 total pieces)
Built To Withstand .50 Cal Recoil
Precision Reflex’s Steel 30mm Scope Rings are built to handle heavy recoil and the inevitable knocks and dings of extreme service. They are machined from tough 4140 carbon steel - not a fancy alloy but one with plenty of strength to handle even the oomph of a .50 caliber - and given a durable, non-reflective black Parkerized finish.
PRI Steel 30mm Scope Rings have four robust Torx-head screws anchoring the ring caps, while a hardened steel crossbolt secured by a hefty 1/2" diameter steel hex nut fixes the ring to the scope base.
- Sold in pairs
- Mounts to standard Picatinny scope bases
- Fits 30mm scope tubes
PRI Steel 30mm Scope Rings are an excellent choice for long-range shooters who demand high-quality and reliability in a scope mounting system.
Provides extra rail room for rear Back Up Iron Sights (BUIS) when using the StrikeFire red dot along with the VMX-3T magnifier. The cantilever ring will move the StrikeFire forward about one inch. Will work with most 30mm red dot sights. Positions red dot sight at either an absolute co-witness height or a lower 1/3 co-witness height.
If you're looking for a solid pair of rings to go with your Leupold BackCountry cross-slot scope base, look no further. The Leupold BackCountry Cross-Slot 30mm Scope Rings are the perfect combination for the company's high-quality bases and are machined from durable 7075 aluminum for added ruggedness, right here in the USA. The rings are finished with a glare-reducing matte-black treatment.
Big Book Catalog, Issue:71, Page:263
Nightforce’s RAP (Ruggedized Accessory Platform) is a handy add-on that enables you to mount a laser, red dot sight, illumination device, or a rail-mount rangefinder directly above your rifle scope. It replaces the top half of a Nightforce X-Treme Duty scope ring to provide you with 4" of MIL-STD 1913 Picatinny rail.
The Nightforce RAP sits just high enough it won’t interfere with the optic. Made of strong yet lightweight machined aluminum, the RAP is sturdy enough to ensure your mounted accessories maintain zero, even under heavy recoil.
- Fits both 4- and 6-screw X-Treme Duty rings
- Matte black hardcoat anodized finish blends with scopes & "Black Rifle" receivers
- Includes all necessary mounting hardware & wrench
- Models to fit 30mm cope rings
When rail space is limited on your rifle, the Nightforce RAP gives you the extra room for the accessories you need. The best part? It’s so close to the scope, you can look through the other device without moving your head!
Promotional Codes are not applicable to Nightforce products.